Bristan CART5 Dual Control Thermostatic Cartridge - 06732COMPL
Dual control brass thermostatic cartridge with ceramic disc valve used in many Bristan shower mixers, which is also known as the CART5.
You might also be interested in
The Shower Doctor Silicone Grease (30ml Tub) - MCSILICONE
Mouldcure Pink and Black Mould Removal Spray (1 litre bottle) - HC0028/1-1/SHO
Product Description
Dual control brass thermostatic cartridge with ceramic disc valve used in many Bristan shower mixers, which is also known as the CART5.
- GTIN: 5014868996745
Important Information
PLEASE NOTE:
This cartridge replaces the CART5 and also is used in the Tivolli & Tivolli II shower
Instructions for the Bristan Thermostatic Cartridge: see diagram above.
Cartridge Removal
- First remove the temperature control handle. See relevant detailed procedure below.
Osborne Art Deco
Unscrew the indice assembly (17), unscrew the retaining screw (19) and pull the handle (9) off the spindle.
Omega
Unscrew the indice cap (15), unscrew the retaining screw (19) remove the ring (14) and pull the handle (9) off the spindle.
Sigma
Remove the plug (13), unscrew the retaining grubscrew (12) and pull the handle(9) off the spindle.
Prism
Unscrew and remove the handle spindle (11), unscrew the retaining grubscrew(10) and pull the handle (9) off the spindle.
Pisa, Orta
Remove the indice (16), unscrew the retaining screw (19) and pull the handle (9) off the spindle. - To remove flow control-handle (8), remove circlip (18) and pull off.
- Remove the two screws and washers (7), the retaining ring (6) and the slip ring(5).
- To remove cartridge (3) pull forward from shower body (1).
Fitting replacement Cartridge
- Ensure that the ceramic disc valve (2) (flow adjustment) is in the off / closed position.
- Grease the seals with silicon grease and carefully refit the cartridge into the body.
- Refit the slip ring (5) and the retaining ring (6) using screws and washers (7).
NB: Please note that the retaining ring (6) should be positioned so that the cartridge has the required 90 degrees of anti-clockwise movement to its open position. If the slots in the ring do not line up with the holes in the body, remove the cartridge and turn it by the required amount and refit. - Refit the flow control handle (8) in the desired 'off' position and fit circlip (18).
- 5) Before refitting temperature control handle reset the Maximum Temperature following the 'Thermotech cartridge commissioning procedure in section 3.
Setting maximum temperature
- Turn on the water supplies and fully open the flow control, let the water run long enough to ensure that the hot water supply is at its maximum temperature.
- First operate the temperature spindle (4) to the extremes of its rotation using the temperature handle if necessary. To set cartridge to desired temperature turn the spindle anti-clockwise to increase the temperature and clockwise to reduce it.
- Refit the temperature control handle by reversing the procedures in section 1 ensuring the stop pin n the handle is at the maximum temperature position.
PLEASE NOTE: If the cartridge is difficult to remove!
Do not try to unscrew the cartridge
Remove the front plate with the two Allen screws the cartridge should just pull out.
If not remove the plug from the body (Opposite side from the hose) you should then be able to get a screwdriver in underneath the cartridge and lever it forward and out.
You can also remove the two inlet elbows this will allow you to get two screwdrivers in to the rear of the cartridge to lever it forward.
Finally if it is a surface mounted valve and you can’t get to the plug or inlet elbows.
Remove the front plate with the two Alan screws, then reassemble the knobs loosely you should then be able to fit two screwdrivers in behind the knobs and lever them forward against the valve body
Service Instructions: Click Here
Product Specification
- Diameter: 42.2mm
- Grub Screw Hole: No
- Length: 133.7mm
- Long Spline: No
- Material: Brass
- Orings: 4
- Spline Tiers: 2
- Teeth: 24
FAQs (112)
Do you have a question regarding this product?
Call us directly 0131 538 4343 or click the button to ask us a question.
Ask a Question
REVIEWS (117)
Have you purchased this product from Shower Doctor?
Why not leave a review here and help other buyers that are looking.
You've seen 5 out of 117 reviews
Delivery
Estimated Delivery: Stocked items usually within 1-3 days, depending on selected delivery option.
Delivery Options: Various delivery options are available including "Next Day" home delivery and Click & Collect from local shops
Order by 3pm for Next Day Delivery option
Returns
If you would like to return any items please send them to:
Returns Department
The Shower Doctor Ltd
Unit 4b, Bankhead Crossway South
Edinburgh
EH11 4EX
When arranging the return yourself, please take a note of any tracking or parcel reference numbers that are provided.
Alternatively, if you would like to use our Royal Mail tracked returns service just follow this link: http://www.royalmail.com/track-my-return/create/5092
The cost for using this service is £3.99 which will be deducted from any refund entitlement.
Please disclose the reason for returning the item along with details of your order number and or account reference.
