Mira

Mira Element Built-in Valve

Product Code: ZMIRA-1.1617.005

Product Discontinued
This product has been discontinued and is no longer available.

We have sold our remaining stock and there are no direct replacements, however if you wish to discuss your options, please do not hesitate to contact us

You might also be interested in

(7)

Universal Superstrong Shower Hose 150cm - 52820

R.R.P £16.80
Our Price
£10.96
Sale
In Stock
(8)

Euroshowers C-Jet Wras Approved Chrome - 56620

R.R.P £16.80
Our Price
£13.80
Sale
In Stock

Product Description

  • Thermostatic temperatures stability keeps showering safe for all the family
  • One single control for flow and temperature creates a clean, minimal look
  • Bulit-in valve only
  • 5 year guarantee

Product Specification

Bringing both thermostatic temperature and flow control onto one simple to use dial, the Mira Element makes showering beautifully simple – and stunningly affordable.

  • Thermostatic temperatures stability keeps showering safe for all the family
  • One single control for flow and temperature creates a clean, minimal look
  • Can be fitted to falling, rising and rear water supplies
  • Approved to TMV2 standards, which means you know its thermostatic control is the very highest quality
  • Clean chrome finish


Technical Information
Principle of Operation

This full thermostatic shower control turns flow on/off and mixes hot and cold water to the desired showering temperature. It automatically compensates for variation in both the temperature and pressure of the inlet water supplies to maintain the blend temperature. If either supply fails the shower control will automatically shut down to prevent scalding.

Limitations of Use
Mira Element should not be used for applications where an outlet flow control forms part of the shower fitting.

Temperature
Maximum inlet hot water temperature: 85°C (BS6700 recommends a maximum of 65°C).
Minimum temperature differential between blend and hot: 12°C
Hot and cold supplies to be a nominally equal pressure
Maximum pressure imbalance: 5:1

Pressure (inlet supplies)

Minimum pressure: 0.1 bar
Maximum maintained pressure: 5.0 bar
Maximum static pressure: 10.0 bar

Performance

The specification performance outlined below is achieved with inlet water supply temperatures of 15°C cold and 65°C hot, and nominally equal inlet supply pressures:
Temperature selection range: full cold to preset maximum (factory set 43°C).
Thermostatic temperature control is achieved in the range 35°C – 45°C
The blended water temperature is maintained within 2°C with a 10°C change in either the hot or cold supply temperatures.
Shutdown to seepage in typically two seconds if either the hot or cold supply fails provided the hot supply is more than 12°C above the blend temperature.
The blended water is maintained within a 2°C range when the pressure of either supply is reduced by 50%.
For high pressure supplies a slow regulator should be fitted to the outlet.

Guarantee

Guaranteed for five years from date of purchase against faulty materials or workmanship.

Application
Mira Element is suitable for installation as part of the following plumbing systems:
Gravity fed
Fully modulating instantaneous gas heated
Mains pressurised (heated from a thermal store)
Unvented mains pressure
Pumped

When the Mira Element is used with mains pressure appliances at pressures above 5.0 bar maintained, a drop-tight pressure reducing valve must be installed to maintain performance.

Installation

The plumbing installation must comply with the requirements of UK Water Regulations/Bylaws (Scotland), Building Regulations or any particular regulations and practices specified by the local water company or water undertakers.
The installation should be carried out by a plumber or contractor who is registered or is a member of an association.
Protect the product from damage when making soldered connections. Some fluxes may cause damage to plastic components.

Mira Element Built-in (shower control only)
Inlet connections: 15mm compression
Outlet connection: 15mm compression
Mounting bracket for thin panel thickness between 4 – 21mm, or sold, dry lined or stud partitioned walls.
Rising and falling inlet supplies go directly into the shower control without the need for additional elbows.
Right-angle hose connector
Built-in shroud for product protection during plastering
Reverse inlet connections supported
Alternative top or bottom outlet supported

FAQs

Do you have a question regarding this product?
Call us directly 0131 538 4343 or click the button to ask us a question.


Ask a Question

Be the first to ask a question about this product.

REVIEWS

Have you purchased this product from Shower Doctor?
Why not leave a review here and help other buyers that are looking.

Submit a review for this product

Be the first to write a review about this product.