MENU

Mira Elite ST Shower Spares

MIRA-PARENT-9

Mira
Mira Elite ST Shower Spareshover to zoom or click to enlargeclick here to view full size

Product Details

Spares
Important Information
***PLEASE NOTE ITEM NUMBER 19 HAS BEEN MODIFIED BY MIRA. PLEASE REFER TO THE LEAFLET SUPPLIED WITH THE PART***
Questions and Answers
Do you have a question regarding this product? Call us on directly 0131 538 4343 or ask us a question now. ? Ask new question

Please fill out the form below to submit your question

You browser doesn't have Flash, Silverlight, Gears, BrowserPlus or HTML5 support.

You browser doesn't have Flash, Silverlight, Gears, BrowserPlus or HTML5 support.

Carbon deposits 1 Answer

Q: Hi there, we've a Mira Elite ST and, on checking the model details etc for a replacement cover, I've found a massive build up of carbon deposits internally. They're everywhere - you cannot see the difference in colour between the live, neutral and earth wires in the connector block. Is this anything to worry about? Everything else it working well - good flow, good heat, etc.



Thanks!

Submitted 230 days ago | by ArcScotland, Edinburgh
! Answer this question
This is the carbon brushes in the motor which may soon need changed,
A:
This should help

http://www.youtube.com/watch?v=pO6IGz4JmtM



Link to brushes

http://www.showerdoc.com/sintech-motor-carbon-brushes-pair-in-brass-casing-01102Answered 230 days ago | Barrie
mira elite st- no hot water 1 Answer

Q: Shower was working before we went on holiday. Came back from two week holiday and can only get cold water now. Any suggestions of what to try please?

Submitted 248 days ago | by Anonymous, wiltshire
! Answer this question

A: If the showeris absolutely cold then I think you may have a faulty Thermal Cut Out
A faulty TCO will have no continuity across the two terminals (Theblack thing on top of the heating tank)
Therefore agood TCO will have power at both connections and a faulty TCO will have power atonly one.
(The function of the TCO is, if thewater over heats it cuts the power off to the elements)

SeeVideo.

http://www.youtube.com/user/showerdoc#p/u/2/_zi8JbEMYMs

If there is some heat it may be a faultyelement in the heating tank (there are two, three in most 10kw showers) you cancheck them with a multi meter you should have a reading of around 12>18 ohms.

If you have power to the elements and noheat it's probably the elements, no power to the elements then it'sprobably a micro switch.

If you don’t have a multimeter we sell themat £10 each with a guide on how to use them for checking and testing the variousparts of your shower.

Apart from helping to fix your shower, theyare really useful for checking you have a power supply to appliances, forchecking fuses, letting you know much power you have left in batteries

(so you know if they aredud or not) and lots of other jobs, in short they are well worth the £10.

http://www.showerdoc.com/installation/electrical-products/SKYTRO-600-005-Digital-Multi-Tester

Answered 248 days ago | Barrie
start/stop button 1 Answer

Q: start/ stop button snapped off my mira elite 2. can this button be fitted seperate to avoid buying full front panel

Submitted 259 days ago | by ann, roscommon ireland
! Answer this question

A: I am afraid Mira only supply it as part of the front cover

Answered 259 days ago | The Doc
cover assembly 1 Answer

Q:  Hi,

just enquiring is item1563-604 cover assembly both front and back or just the front cover?

Thanks.

Submitted 304 days ago | by Andy, Dublin. Ireland
! Answer this question
A: This is just the front cover.Answered 303 days ago | Barrie
Mira Elite Leak at Inlet Clamp 1 Answer

Q: I have a leak at the shower inlet, it looks like the inlet clamp mira 416.38 has cracked. Is it sufficient to replace the clamp or is there also a washer that needs to be replaced?

Submitted 317 days ago | by Hugh, Ireland
! Answer this question

A: Yes replacing the clamp will normally fix any leaks here.

However..... If the rear case is cracked then you will havereplace the shower as the case is not available as a spare.

Also check the way the connector fits into the bracket andclamp, the most normal cause of this part splitting is that the connector isnot absolutely square as it enters the shower

Answered 316 days ago | The Doc
elite st tripping out oh high 1 Answer

Q: I have tested the elements and have a reading on front 1 but not rear 1 does that mean it's the thermal switch that's faulty

Submitted 326 days ago | by alan, essex
! Answer this question
A: No it means that one of the can elements is faulty and that the can needs replaced.Answered 325 days ago | Barrie
mira elite shower no temp control 1 Answer

Q: water is either way too hot or freezing cold when you adjust,in high setting same for medium,head is clean as is filter,temp switch is giving continuity

Submitted 331 days ago | by duff, woking
! Answer this question

A: Forgetting about the temperature, turn the showerfrom fully hot to fully cold. At fully hot you should have not much more than adribble coming from the hose, and on fully cold you should have a good strongflow. If you do not have this difference then you may have a faultyflow/stabilizer valve.

Answered 330 days ago | Barrie
elite st tripping 1 Answer

Q: My elite st shower tripps out on high setting only

Submitted 331 days ago | by alan, essex
! Answer this question

A: It may be a faulty elementin the heating tank (there are two, three in most 10kw showers) you can checkthem with a multi meter you should have a reading of around 12>18 ohms.

If you have power to theelements and no heat it's probably the elements, no power to the elements thenit's probably a micro switch.

If you don’t have amultimeter we sell them at £10 each with a guide on how to use them forchecking and testing the various parts of your shower.

Apart from helping to fixyour shower, they are really useful for checking you have a power supply toappliances, for checking fuses, letting you know much power you have left inbatteries

(so you know if they are dud ornot) and lots of other jobs, in short they are well worth the £10.

http://www.showerdoc.com/installation/electrical-products/SKYTRO-600-005-Digital-Multi-Tester

Answered 331 days ago | Barrie
mira elite 1 Answer

Q: water stops showering while in use.next day it dose the same.you can here pump working.

now switch on and only pump works but no water showering.

filter is clean and plenty of water flowing from main water supply to filter housing

thanks.

Submitted 337 days ago | by help please, galway ireland(tuam)
! Answer this question

A:  I think you may have a faulty solenoid,

http://www.showerdoc.com/mira-solenoid-coil-416-51

 however if the solenoid is faulty you are probably better just replacing the complete flow valve as the solenoid comes as part of the flow valve.

http://www.showerdoc.com/mira-flow-valve-assembly-comes-with-coil-and-switch-1563-507

Answered 336 days ago | The Doc
mira elite 1 Answer

Q: pump working,no water shower.

filter is clean and plenty of water flow.

bled system as directed.



history.

at first it would stop showering while in use.next day it would do the same.now,no water shower at all.

thanks

Submitted 337 days ago | by Anonymous, Unknown
! Answer this question
<strong>A: </strong>Ticket Answers for FAQs - Solenoid Check 1

It may be your solenoid valve, you can check it if you have a multi meter, you should have a reading of at least k3.5 ohms, across the two terminals any less and you need a new valve. (Check the valve in the failed state.) (When it has stopped working!)

If there is power getting to the solenoid and it is not operating then there is a good chance that you have a faulty solenoid.

http://www.youtube.com/watch?v=NzJjzWqxesc

The video is intended as a guide and does not cover every shower.

If you don’t have a multimeter we sell them with a guide on how to use them for checking and testing the various parts of your shower.

Apart from helping to fix your shower, they are really useful for checking you have a power supply to appliances, for checking fuses and letting you know much power you have left in batteries

(So you will know if they are good or not) and lots of other jobs, in short they are well worth a few pounds

http://www.showerdoc.com/installation/electrical-products/SKYTRO-600-005-Digital-Multi-Tester

Answered 337 days ago | LC
mira elite st 1 Answer

Q: my shower is leeking after it is turned off and water is scalding

Submitted 344 days ago | by curly, eire
! Answer this question
Where is it leaking from?
A: If it is from the head then,

it maybe your solenoid valve, you can check it if you have a multi meter, you shouldhave a reading of at least k3.5 ohms, across the two terminals any less and youneed a new valve. (Check the valve in the failed state.) (When it has stoppedworking!)

If thereis power getting to the solenoid and it is not operating then there is a goodchance that you have a faulty solenoid.

http://www.youtube.com/watch?v=NzJjzWqxesc

The video is intended as a guide and does not cover every shower.

If youdon’t have a multimeter we sell them with a guide on how to usethem for checking and testing the various parts of your shower.

Apart from helping to fix your shower, they are really useful forchecking you have a power supply to appliances, for checking fuses and lettingyou know much power you have left in batteries

(So youwill know if they are good or not) and lots of other jobs, in short they arewell worth a few pounds

http://www.showerdoc.com/installation/electrical-products/SKYTRO-600-005-Digital-Multi-Tester

Answered 344 days ago | Barrie
Part nr: MIRA-1563.604 1 Answer

Q: Do you have it in stock at the moment. If not when expected in?

Submitted 375 days ago | by Pathfinder, Malahide
! Answer this question

A: Not in stock at the moment, available for dispatch 3-7 days

Answered 374 days ago | The Doc
Mira Elite ST Not Water Output 1 Answer

Q: I have a Mira Elite ST that switches on when the power switch is pressed. It sounds as if the pump is operating correctly however no water reaching the shower head. Checked the water inlet and no issues there, also the filter is clear.

Can you help me? Dol I need to replace the flow valve assembly with the solenoid and switch? Don't have an ohm meter but getting continuity across the coil. Thanks.

Submitted 463 days ago | by tarrapoto, Galway
! Answer this question

A: Almost certainly a faulty solenoid in the flow valve, thebest solution is to replace the complete flow valve assembly.

http://www.showerdoc.com/mira-flow-valve-assembly-comes-with-coil-switch-1563-507

Answered 462 days ago | The Doc
mira elite st 9.8kw 1 Answer

Q: the water keeps flowing from base of heater tank weather shower turned on /off

Submitted 491 days ago | by speedy, Unknown
! Answer this question

A: Ithink the Pressure Relief Device (PRD) has blown.

It’sa safety device on the bottom of the heating tank.

Itis fairly easy to replace however there is usually something that causes it toblow, oftena kink in the hose or the showerhead is blocked, so check this before fittingthe new PRD.

Answered 491 days ago | Barrie
no hot water 1 Answer

Q: no hot water coming from shower.



removed cover

live on both sides of the CTO when shower is off

but only on inward side of CTO when I turn on the shower



I this a CTO problem??

Submitted 559 days ago | by joedev, ireland
! Answer this question

A: I haven’t heard of this problem before.

Are you sure you are testing the Thermal Switch (TCO)correctly?

There is a video clip half way down this page that shows howto check the TCO, have a read at the instructions below and if this doesn’tsolve the problem get back to us.

If the shower is absolutely cold then I thinkyou may have a faulty Thermal Cut Out
A faulty TCO will have no continuity across the two terminals(The black thing on top of the heating tank)
Therefore a good TCO will have power at both connections and afaulty TCO will have power at only one.
(The function of the TCO is, if the water over heats it cuts thepower off to the elements)

See Video.

http://www.youtube.com/user/showerdoc#p/u/2/_zi8JbEMYMs

Ifthere is some heat it may be a faulty element in the heating tank (there aretwo, three in most 10kw showers) you can check them with a multi meter youshould have a reading of around 12>18 ohms.

If you have power to theelements and no heat it's probably the elements, no power to theelements then it's probably a micro switch.

If you don’t have amultimeter  we sell them at £10 each with a guide on how to use them forchecking and testing the various parts of your shower.

Apart from helping to fix yourshower, they are really useful for checking you have a power supply toappliances, for checking fuses, letting you know much power you have left inbatteries

(so you know if they are dud ornot)  and lots of other jobs, in short they are well  worth the £10.

http://www.showerdoc.com/installation/electrical-products/SKYTRO-600-005-Digital-Multi-Tester

Answered 556 days ago | The Doc
Water still flows and cycles hot cold when turned off 1 Answer

Q: When i switch the switch the shower off at the unit the water still flows and cycles hot and cold, i wait till the water is cold and turn off the electric at the pull cord and then the water will stop between 5 and 10 mins.

Can you help or suggest what need replacing.

Thanks

Ian

Submitted 591 days ago | by Anonymous, West Somerset
! Answer this question

A: If when you switch off the shower at the main isolator and the shower keeps running then you have a faulty solenoid.

When you switch off the shower at the main isolator and the water stops running, then you have a faulty on/off switch or a faulty PCB or a micro switch that is sticking on.

Answered 591 days ago | Barrie
Water goes cold 30Sec after warming up 1 Answer

Q: Hi, I've got a Mira Elite ST 9.8Kw unit, which has developed a fault. Turn it on, good flow, water warms up as normal, then 20-40 Sec it goes cold. I can tell that power is switched off to heater as pump speeds up ever so slightly. At this point it goes cold, but still has a good flow. After a delay it will start to heat water again, then repeats the cycle.

I have cleaned the filter, slight amount of sediment was present, this didnt fix the problem.

Which part should I replace to fix this?



Another question, will a 10.8Kw unit fit in place of a 9.8Kw unit?

Submitted 597 days ago | by Anonymous, Cowling
! Answer this question

A: I think you may have a faulty Thermal Cut Out (TCO).

A faulty TCO will have no continuity across the two terminals (The black thing on top of the heating tank)

Therefore a good TCO will have power at both connections and a faulty TCO will have power at only one.

(The function of the TCO is, if the water over heats it cuts the power off to the elements until the water cools, this can take up to 15mins)

See Video:

http://www.youtube.com/user/showerdoc#p/u/2/_zi8JbEMYMs

After fitting a new TCO

When fitting a new TCO listen to the shower, after it has completed its first on/off cycle, if when it is switched off you hear it continuing to heat (Noise like a kettle starting to boil) this will mean that there is a switch or a relay that is stuck in the on position, this is keeping an element energised and this is probably what caused the original TCO to fail.

If this is the case replace the faulty switch or relay and make sure that you switch the shower off at the isolating switch when the shower is not in use because this may cause the new TCO to fail.

Answered 597 days ago | Barrie
Mira Elite ST Load Noise 1 Answer

Q: I have a Mire Elite ST for about three years. Gets a lot of use (two teenage daughters). In the last couple of days it has started making a load noise when running. Sounds like it could be motor/pump. I have an older model mira elite in the attic, held on to it when i replaced with the new one. Maybe i can take the motor/pump from the old one?



Any help appreciated.

Submitted 599 days ago | by marko74, Ireland
! Answer this question
You are in the best position to tell. Have a look, as the older version had the same motor, unless it was the very old model.
A:
http://www.showerdoc.com/shower-spares/mira/mira-parent-8-mira-elite-2Answered 598 days ago | Barrie
ST tripping out 1 Answer

Q: Mira Elite ST tripping out the main circuit breaker on High setting. Also tripping out on Medium with a warmer setting. Not tripping out on Medium with the cooler setting. Not tripping out on Cold, Appears to heat up on Meduium with lower setting. Is the heating tank U/S??

Submitted 605 days ago | by Pete, Aberdeenshire
! Answer this question
A: Yes it does sound as if your heating can is to blame.Answered 604 days ago | Barrie
mira elite st steams 1 Answer

Q: when you turn off the shower you can here the boiler bubbling an then steam sprays out the nozzle for about 3 secs

Submitted 623 days ago | by tony, cork ireland
! Answer this question

A: It is likely that one of the micro switches is stuck in the on position keeping one of the elements energised, or one of the paddles on the flow valve has stuck and is keeping one of the micro switches in the on position.

Until you get this repaired operate the shower from the isolation switch as a temporary measure

Answered 623 days ago | The Doc
no hot water 1 Answer

Q: No hot water when on any setting,we switched it off n tried it again the next day in which hot water was working again but there was a more rebust sound coming from shower,wat wud be the cause of this plz

Submitted 630 days ago | by wad, ireland
! Answer this question
Check the inlet filter, part 18 , then,
A:

If the shower is absolutely cold then I think you may have a faulty Thermal Cut Out
A faulty TCO will have no continuity across the two terminals (The black thing on top of the heating tank)
Therefore a good TCO will have power at both connections and a faulty TCO will have power at only one.
(The function of the TCO is, if the water over heats it cuts the power off to the elements)

See Video.

http://www.youtube.com/user/showerdoc#p/u/2/_zi8JbEMYMs

If there is some heat it may be a faulty element in the heating tank (there are two, three in most 10kw showers) you can check them with a multi meter you should have a reading of around 12>18 ohms.

If you have power to the elements and no heat it's probably the elements, no power to the elements then it's probably a micro switch.

If you don’t have a multimeter we sell them at £10 each with a guide on how to use them for checking and testing the various parts of your shower.

Apart from helping to fix your shower, they are really useful for checking you have a power supply to appliances, for checking fuses, letting you know much power you have left in batteries

(so you know if they are dud or not) and lots of other jobs, in short they are well worth the £10.

http://www.showerdoc.com/installation/electrical-products/SKYTRO-600-005-Digital-Multi-Tester

Answered 629 days ago | Barrie
Mire Elite st 1 Answer

Q: When I switch the shower on the swithch bounces back out and switches off, have to wedge the button to have a shower.

Submitted 634 days ago | by gavman, northampton
! Answer this question
This is the replacement part,
A:
http://www.showerdoc.com/shower-spares/mira/electric-showers/mira-416-48-mira-latching-switch-416-48Answered 633 days ago | Barrie
Mira Elite st shower 1 Answer

Q: Have water before pump and filter clean but no water pumping through shower head even when it is turned to a cool setting. No problem with power (230 volts) and can see pump fan turning and making noise.

Submitted 722 days ago | by boy, Unknown
! Answer this question

A:

Itmay be your solenoid valve, you can check it if you have a multi meter,you should have a reading of at least k3.5 ohms, across the twoterminals any less and you need a new valve. (Check the valve in thefailed state.) (When it has stopped working!)

If there is power getting to the solenoid and it is not operating then there is a good chance that you have a faulty solenoid.

http://www.youtube.com/watch?v=NzJjzWqxesc

The video is intended as a guide and does not cover every shower.

If you don’t have a multimeter  we sell them  with a guide on how to use them for checking and testing the various parts of your shower.

Apartfrom helping to fix your shower, they are really useful for checkingyou have a power supply to appliances, for checking fuses and lettingyou know much power you have left in batteries

(So you will know if they are good or not) and lots of other jobs, in short they are well worth a few pounds

http://www.showerdoc.com/installation/electrical-products/SKYTRO-600-005-Digital-Multi-Tester

Answered 721 days ago | Barrie
mira elite st 1 Answer

Q: when turned on makes a noise from the motor, an sparks, also water is very low pressure.

Submitted 730 days ago | by Anonymous, Unknown
! Answer this question
First check the filter is not blocked, part 18 on the diagram below, then the hose and head for restrictions.
A:
http://www.showerdoc.com/shower-spares/mira/electric-showers/mira-parent-9-mira-elite-stAnswered 729 days ago | Barrie
shower keeps leeking from the mira filter 1563.691 1 Answer

Q: once taken apart and re put seal on it seems to stop 4 a week then start again

Submitted 745 days ago | by hinezy, essex
! Answer this question

A: All I can think of is to check that the ‘O’ ring is OK andthat it is sitting properly into place, I guess that the other option is toreplace the filter assembly

http://www.showerdoc.com/MIRA-1563-679-Mira-Filter-Assembly-Spare-1563-679

Answered 744 days ago | The Doc
Carbon Brushes for Mira Elite ST 1 Answer

Q: Having purchased these from you in the past I am alarmed to see you now list them as obsolete.

Do you list an alternative?

Submitted 754 days ago | by Kevin, Billericay essex
! Answer this question
A: Sorry, to date wed have not been able to source a supplier of these parts.Answered 752 days ago | Barrie
on off switch 1 Answer

Q: It is very hard to turn on the shower on and off,when I take the cover off the switch works ok and turns the shower on and off it appears that the on off button does not engage with switch.

this seems to of only happens after I changed the solenoid coil.

Submitted 757 days ago | by Anonymous, galway,ireland
! Answer this question

A: Sounds like that when you have fitted the solenoid that somethingis not perfectly realigned.

The most likely problems are the flow valve locates on pinsin the rear case, make sure that they locate perfectly into place also there isa sort of hook that holds the flow valve and the heater tank together, makesure that they are properly in place.

Answered 756 days ago | The Doc
Mira Elite st 1 Answer

Q: My Mira Elite st the water is continually running when shower off, power on or off.Before it happened there was a kind of grinding noise or slow whirring noise.Water supply ok water getting

hot when shower working but dial has to be nearly on max setting and still its not the same as before.

Any ideas guys/girls??



Submitted 858 days ago | by gazzer1, Unknown
! Answer this question

A: I think you need a new flow control valve assembly also check that the inlet filter is clear.

http://www.showerdoc.com/shower-spares/mira/MIRA-1563-507-Mira-Flow-Valve-Assembly-1563-507

Answered 857 days ago | The Doc
swithching on the mira 1 Answer

Q: when i press the on switch it does not engage . when i take my finger off it the shower switches



what is wrong and what part do i need

Submitted 885 days ago | by mikey, dublin
! Answer this question

A: From your description it sounds like a faulty latching switch.

http://www.showerdoc.com/MIRA-416-48-Mira-Latching-Switch-416-48

http://www.showerdoc.com/mira-parent-9-mira-elite-stAnswered 884 days ago | The Doc
Mira Elite st going hot / cold 1 Answer

Q: When show is in use the water get hot and cold can i get part to repair same

Submitted 900 days ago | by JBB, limerick Ireland
! Answer this question

A: First check that the inlet filter is clear

If this is OK and the pump sounds like it is running OK then it is likely to be your flow valve that is at fault.

http://www.showerdoc.com/shower-spares/mira/MIRA-1563-507-Mira-Flow-Valve-Assembly-1563-507

Answered 899 days ago | The Doc
No hot water 1 Answer

Q: put new flow valve in as water didn't switch off. Now that's OK but no HOT water

Submitted 936 days ago | by Sue, Pembrokeshire
! Answer this question
Check that the levers in the flow valve are actuating both microswitches when shower is on and full power is selected.
A: Check the thermal switch on top of the heating can for continuity , if open circuit a replacement is required , it can be ordered online by clicking on the link below.

http://www.showerdoc.com/shower-spares/mira/MIRA-416-41-Mira-Thermal-Switch---416-41Answered 934 days ago | Alastair
Mira St thermal switch 1 Answer

Q: I have a Mira Elite ST 10.8 W and the thermal switch has gone faulty 8 times since it was installed in February 2010. On average breaks down after about two months. What could be the cause for such frequent breakdown. Mira even replaced the whole shower unit once. It is under guarantee so Mira engineers fix it but don't have an explanation why the thermal switch goes faulty so quickly. Any suggestions!!

Thank you. Ranj

Submitted 959 days ago | by Ranj, West London
! Answer this question
One other thought.
A:

After fitting a new TCO

When fitting a new TCO listen to the shower, after it has completed its first on/off cycle, if when it is switched off you hear it continuing to heat (Noise like a kettle starting to boil) this will mean that there is a switch or a relay that is stuck in the on position, this is keeping an element energised and this is probably what caused the original TCO to fail.

If this is the case replace the faulty switch or relay and make sure that you switch the shower off at the isolating switch when the shower is not in use because this may cause the new TCO to fail.

Answered 955 days ago | The Doc
break down of thermal switch on Elite ST 10.8 kW 1 Answer

Q: The thermal switch on the Elite ST 10.8 kW breaks down very often. On the last occasion it lasted only four showers. What could be the reason.

Submitted 1053 days ago | by Jit, Hounslow
! Answer this question
A: Check that the top of the heating can where it sits is not deformed and that the holding pillars are square to the flat top as the most likely explanation is distortion of the mounting putting stress on the bi-metallic operating disc in the switch.Answered 1053 days ago | Alastair
Mira Elite ST - No water flow 1 Answer

Q: The water has stopped flowing, the low flow light comes on at any temperature and the motor has recently changed tone. All pipes & filters etc are clear. The unit has been getting very warm but assumed that was the pump working. What is the problem, how do we fix it?

Submitted 1066 days ago | by Jane, Kendal
! Answer this question

A: I think you need a new flow valve assembly.

Answered 1066 days ago | The doc
Mira Elite ST cannot adjust 1 Answer

Q: OK have Mira elite st when I turn off the shower the water keeps coming for a while don't seem to be able to control the temperature? have it set to high, 3 to 4 digits above red digits but if I turn it to cold still stays at same temperature area water "soft.

Submitted 1114 days ago | by telsey, Ireland
! Answer this question

A: Make sure that the valve on the line to the shower is fully open, then check the inlet filter is clean and the shower head is also clear, if all these ate OK then you are going to need a new flow valve.

http://www.showerdoc.com/shower-spares/mira/MIRA-1563-507-Mira-Flow-Valve-Assembly-1563-507

Answered 1113 days ago | The Doc
mira elite going hot / cold 1 Answer

Q: Water is going frm hot to cold. no contrl over temp of water

Submitted 1137 days ago | by derm, Galway, |reland
! Answer this question

A: The things to check first are.

1 Check that the valve on the line to the shower is fully open.

2 Check that the inlet filter is clean and clear

If the valve is not fully open then there may not be enough water
getting to your shower to cool it properly the overheat safety device will turn
the power off until it cools Then it all starts again

Make sure that the shower head is clean and clear, that the hose isn’t kinked (this can happen just behind the hand set where it is difficult to see) also check the inside of the hose although it can look OK on the outside it could have collapsed internally

If all of these are OK then you probably need a new flow valve assembly.

http://www.showerdoc.com/shower-spares/mira/MIRA-1563-507-Mira-Flow-Valve-Assembly-1563-507

Answered 1136 days ago | The Doc
Water stops flowing 1 Answer

Q: the water stops flowing and low flow light comes on after 2 mins approx

On high setting...

But when on lowest setting water flows ok

Submitted 1163 days ago | by larasta, dublin
! Answer this question

A:  I think you need a new flow valve.

Here is the link.

http://www.showerdoc.com/shower-spares/mira/MIRA-1563-507-Mira-Flow-Valve-Assembly-1563-507

Answered 1162 days ago | The Doc
On/Off button 1 Answer

Q: The on/off button has fallen off, is it possible to replace it or do I nee a new cover assembly? If I need a new assembly how do I fit it?

Submitted 1169 days ago | by Rick, Newent, Glos.
! Answer this question
The on/off button is an integral part of the front cover assy which can be ordered online by clicking on the link below.
A: To replace the cover set the 2 control knobs to the 12 o`clock position then remove the 4 holing screws 2 at top and 2 at bottom of casing.
Set the knobs on the new  cover to 12 o`clock and fit on and replace holding screws.

http://www.showerdoc.com/shower-spares/mira/MIRA-1563-604-Mira-Cover-Assembly-1563-604Answered 1168 days ago | Alastair
water keeps flowing after shower is turned off 1 Answer

Q: what is problem

Submitted 1206 days ago | by colin, dublin
! Answer this question

A: I think you are going to need a new flow valve.

Here is the link.

http://www.showerdoc.com/shower-spares/mira/MIRA-1563-507-Mira-Flow-Valve-Assembly-1563-507

Answered 1204 days ago | Anonymous
mira elite st 1 Answer

Q: shower running but no hot water running on any settings . cleaned filter but did not solve problem . is there any way of knowing whether it is the thermal switch or heater tank which is to fault , cheers john the novice .

Submitted 1211 days ago | by novice, kildare, ireland
! Answer this question

A: It may be a faulty element in the heating tank (there are two, three in 10kw showers) you can check them with a multi meter you should have a reading of around 12>18 ohms.

If you have power to the elements and no heat it's probably the elements, no power to the elements then it's probably a micro switch.

 

If you don’t have a multimeter  we sell them at £10 each with a guide on how to use them for checking and testing the various parts of your shower.

 

Apart from helping to fix your shower, they are really useful for checking you have a power supply to appliances, for checking fuses, letting you know much power you have left in batteries

(so you know if they are dud or not)  and lots of other jobs, in short they are well  worth the £10.

http://www.shower-warehouse.co.uk/erol.html#55x878

The thermal cut out on top of the heating can should be tested for continuity using the meter .

Once you have established which part is at fault replacement can be ordered online via the link below.


http://www.showerdoc.com/shower-spares/mira/MIRA-PARENT-9-Mira-Elite-ST 

Answered 1206 days ago | Alastair
low flow light coming on 1 Answer

Q: Shower gets very hot on max setting and low flow light comes on when turned down , too cold on medium setting

Submitted 1311 days ago | by none
! Answer this question
If you click on the link below it will take you to an exploded diagram, check tha the inlet filter item 18 is clean. If it is ok then it may be yhe motor pump ass thatb needs replaced, it can be ordered online via this link also.
A:
http://www.showerdoc.com/shower-spares/mira/MIRA-PARENT-9-Mira-Elite-STAnswered 1310 days ago | Alastair
Customer Reviews
Be the first to write a review about this product.
Replacement Products
Related Spares

Please call for more information on available spares for this product

Express UK Deliveries
7 Day Money Back Guarantee