Q: Hi,
I'm looking for the direct replacement slide bar and shower cradle. Do you know what I require. The shower is a Mira events thermostatic es. I must of had this shower for 10 years.
Thanks in advance..
|
|
|
Submitted 25 days ago | by
Barry, Sidcup
Answered 23 days ago | Barrie
|
|
|
Q: Hi, I have a problem with my power shower event xs. The on/off button will not stay on unless it is held on. I have replaced with a new item C on diagram, this worked for 3 days and now it is doing the exact same thing! Please help.
|
|
|
Submitted 37 days ago | by
Bex, Lincs
A: Sounds like a faulty, on/off switch, again. To test this you need to try the switch with the cover off. If it wont work this way then it is the switch again, if it does work then it is the button on the cover. Answered 36 days ago | Barrie |
|
|
Q: Flow control no longer works and is stuck on high flow. I have taken off the cover and checked the spindle to confirm it no longer works. Can you recommend parts needed or further checks to make?
|
|
|
Submitted 107 days ago | by
Digaholedug, Gloucestershire
Answered 106 days ago | The Doc
|
|
|
Q: replacement for meynell vitesse
|
|
|
Submitted 108 days ago | by
norman, harrogate
Answered 107 days ago | The Doc
|
|
|
Q: motor runnig but no water coming into hose
|
|
|
Submitted 122 days ago | by
alvin, irleand
Answered 122 days ago | The Doc
|
|
|
Q: the shower shuts down after 2-3 mins of running and no water comes out .
|
|
|
Submitted 130 days ago | by
nobby, hawick
A: If you have a Mira advance then you will need a new relayboard The question came from a Mira event page if you have anEvent then you will probably need to change the solenoid valve. Answered 130 days ago | The Doc A: If you have a Mira advance then you will need a new relayboard The question came from a Mira event page if you have anEvent then you will probably need to change the solenoid valve. Answered 130 days ago | The Doc |
|
Q: Start button does not stay on - if you remove your finger the water stops.
Everything else seems to work normally
|
|
|
Submitted 155 days ago | by
Bill, Chippenham
Answered 150 days ago | Alastair
|
|
|
Q:
|
|
|
Submitted 172 days ago | by
brizo, fife
A: You may be having a problem with the motor and pump unit, however the first thing to check is the filters, make sure that they are clean and clear. Answered 170 days ago | The Doc |
|
|
Q: Our shower continues to drip water after being turned off. This isn't a big leak but it seems to continue, leaking around a litre in 24 hours. It's obviously more than just water left in the shower head. Does this sound like the solenoid valve needs to be replaced?
|
|
|
Submitted 177 days ago | by
Chris, Shropshire
A: Sorry for the delay in replying. It needs a new solenoid valve Answered 171 days ago | The doc |
|
Q: Pressing the on/off button will not turn on the shower. What could the possible reasons be?
Thanks
|
|
|
Submitted 204 days ago | by
Ken, Unknown
A: If there is no water and you can hear the motor running then you probably have a faulty solenoid valve. If the water is running and there is no noise from the motor then you probably have a faulty motor and pump unit. If there is no water and no noise you may have a faulty switch, which is part of the wiring loom Answered 204 days ago | The Doc |
|
|
Q: I have a 10 year old Mira event thermostatic power shower and the brushes are burnt out . The water will still run out if you turn the button but no power it only runs out like a hose . Do I need a new shower .
|
|
|
Submitted 210 days ago | by
Dawn, Northern Ireland
Answered 208 days ago | Alastair
|
|
|
Q: mira event xs thermostatic shower works ok but noisy
|
|
|
Submitted 233 days ago | by
hoppy, leeds yorkshire
A: Probably just the bearings in the motor and pump unit starting to fail. They can carry on like this for some time, however most people replace it when it starts to waken their neighbours! J Answered 232 days ago | The Doc |
|
Q: I have a Mira Event XS Thermostatic power shower, over the last few days it continues to let water come through, with no pressure, after the shower stop button has been pushed. This lasts for about 3 minutes in total then it does eventually stop.....please help?
Thanks
|
|
|
Submitted 239 days ago | by
Anonymous, Aylesbury
Answered 237 days ago | Alastair
|
|
|
Q: Hi, just got a new house with one of these in, but it only runs cold, the hot supply pipe heats up tho - so some hot must be runing in - but on any power setting or heat setting - can only get cold out. Please advise what probable problem is?
|
|
|
Submitted 243 days ago | by
Tim, Poole
Answered 242 days ago | Alastair
|
|
Q: The Shower hose keeps falling out of the Shower where it is attached to part D1532104 B. (Part H in the diagram) The screw ridges have worn away.
What can I do?
|
|
|
Submitted 248 days ago | by
diane, bedford
Answered 248 days ago | Anonymous
|
|
Q: Shower working normally, then water dies away. Tried again but no water. Tried a further time a few hours later and all seemed to be working OK. Then water died away to zero flow, but pump still running. Checked filters (OK), read your site and checked solenoid (has a resistance of c. 1 MegaOhm). I am assuming a faulty solenoid has a higher resistance than your quote for a working one (c. 3.5 K Ohm).
Is this correct ?
|
|
|
Submitted 249 days ago | by
NigelB, Unknown
Answered 246 days ago | Alastair
|
|
Q: Where Start/Stop switch was is just a hole now and shower cannot be turned on or off using this button.
Is the shower unit irrepairable ?
Thanks
|
|
|
Submitted 271 days ago | by
Chris, Surrey
Answered 271 days ago | LC
|
|
Q:
Hi, our shower has gotten louder last couple of weeks. And dirty water is coming from where hose is connected. Any ideas? Thanks in advance.
|
|
|
Submitted 313 days ago | by
Steve, Glasgow
A: First check that the filters are clean and clear if they are OK then it probably is your motor and pump unit bearings starting to fail. Answered 312 days ago | The Doc |
|
|
Q: I have had this mira shower for three years now, its always been noisy, & now has packed up altogether, checked the brushes seem ok, tested solonoid good reading, the pump seems to be quite stiff to turn so not shaw weather to purchase new motor? any ideas.? cheers.
|
|
|
Submitted 331 days ago | by
mint, Cirencester.
Answered 327 days ago | Alastair
|
|
Q: Like others here our front cover has popped off the shower and the button is getting more difficult to operate.
I understand I need part number 6 but how easy is to get the old cover off, I can two screws on top and one on the bottom but how does the temperature and showere preassure knob come off?
|
|
|
Submitted 342 days ago | by
Dave, Exmouth
A: The temperature knob just pulls forward, the on/off and flow are part of the front cover. Answered 339 days ago | The doc |
|
|
Q: no water comes out of my shower even tho its turned on and working??
|
|
|
Submitted 366 days ago | by
jj, ireland
A: It may be your solenoid valve, you can check it if you have a multi meter, you should have a reading of at least k3.5 ohms, across the two terminals any less and you need a new valve. (Check the valve in the failed state.) (When it is not working!) If there is power getting to the solenoid and it is not operating then there is a good chance that you have a faulty solenoid. If you don’t have a multimeter we sell them with a guide on how to use them for checking and testing the various parts of your shower. Apart from helping to fix your shower, they are really useful for checking you have a power supply to appliances, for checking fuses and letting you know much power you have left in batteries (So you will know if they are good or not) and lots of other jobs, in short they are well worth a few pounds http://www.showerdoc.com/installation/electrical-products/SKYTRO-600-005-Digital-Multi-Tester Answered 365 days ago | The Doc |
|
|
Q: We have just bought a house with the power shower in the en-suite. It is fed by a hot water tank. The hot water is on all the time to ensure we have it whenever we want. The shower will run for awhile and then when I am trying to rinse my hair ( it always happen to me, not my partner) the shower makes a really funny noise like the pump is struggling and then it stops and there is no hot water or any water coming out. Even switching it off and then back on does not make any difference. This has happened both when I've been in the shower for a couple of minutes and also when just starting the shower up. There is no set pattern to it. What is wrong with it?
|
|
|
Submitted 372 days ago | by
Sam, Leeds
A: It may be your solenoid valve, you can check it if you have a multi meter, you should have a reading of at least k3.5 ohms, across the two terminals any less and you need a new valve. (Check the valve in the failed state.) (When it is not working!) If there is power getting to the solenoid and it is not operating then there is a good chance that you have a faulty solenoid. If you don’t have a multimeter we sell them with a guide on how to use them for checking and testing the various parts of your shower. Apart from helping to fix your shower, they are really useful for checking you have a power supply to appliances, for checking fuses and letting you know much power you have left in batteries (So you will know if they are good or not) and lots of other jobs, in short they are well worth a few pounds http://www.showerdoc.com/installation/electrical-products/SKYTRO-600-005-Digital-Multi-Tester Answered 372 days ago | TheeDoc |
|
|
Q: My shower is about 7 years old. All of a sudden there is a problem when turning the setting to warm water. The flow reduces dramatically and the pump makes a different noise. Can you advise on the best course of action?
|
|
|
Submitted 384 days ago | by
Gareth, Penllergaer
A: See Ticket 18126 Answered 382 days ago | The doc |
|
|
Q: Where can I purchase a micro switch for a Mira Event XS Thermostatic power shower
|
|
|
Submitted 406 days ago | by
soapy, Bournemouth
Answered 406 days ago | The Doc
|
|
Q: Often while shower is working normally, the pitch of the motor sound will rise and the flow rate drops. Teperature stays OK. Temporary fix by turning motor to max for a few seconds, but problem becoming more frequent.
Do I need a new pump assembly or a whole new unit
|
|
|
Submitted 416 days ago | by
Alan, Mlavern, Worcestershire
A: I think the first thing I would do would be to check that the filters are clean and clear, also check that the head is also clear. You may just need a new set of brushes. Answered 416 days ago | The Doc |
|
Q: I have a shower that needs to be looked at. It is leaking water from the unit down the cord. It also seems to be struggling when it runs - it is making an excessive noise on occasion.
Any ideas ?
Shring
|
|
|
Submitted 435 days ago | by
Shring, Herts
Answered 434 days ago | The Doc
|
|
|
Q: This morning the oval on/off switch failed to operate the shower and it feels as though the 'spring' or mechanism behind the button has failed. The button is now sitting in what should be the on position but the shower is not operating. I have tried to remove the casing to look behind but can't seem to get the casing off as it seems to be fixed at the bottom. I have removed the 2 top and 1 bottom screws but no success. How do you suggest I get this sorted? Many thanks
|
|
|
Submitted 450 days ago | by
Robin, Scotland
Answered 449 days ago | Alastair
|
|
Q: Temperature Hub Retaining Screw what size screw is it?
|
|
|
Submitted 451 days ago | by
alf, horley
Answered 450 days ago | The Doc
|
|
|
Q: i am wondering if i can get a replacement switch for this shower
|
|
|
Submitted 456 days ago | by
andy, northern ireland
Answered 455 days ago | Alastair
|
|
|
Q: where can i buy carbon brushes for event xs
|
|
|
Submitted 473 days ago | by
strats, hants
Answered 470 days ago | Alastair
|
|
|
Q: Shower will not stay on unless one keeps power button depressed. Power on/off switch is not faulty as I have checked it with power off. However, the power switch will not stay on when power restored. It looks like an auto shut off is taking place. What could be causing this?
|
|
|
Submitted 496 days ago | by
Noel, Ireland
A: There is no auto shut off for this shower. A faulty on/off switch is not an uncommon fault with this shower, however you say that the switch is OK...... Sorry but I can’t think of any other fault than the on / off switch, I would be happy to be proved wrong! Answered 494 days ago | The Doc |
|
|
Q: hi the shower will not stay on, unless you hold the on button in? What do you think i need?
|
|
|
Submitted 534 days ago | by
geoff, ireland
Answered 532 days ago | The Doc
|
|
|
Q: The shower head continues to drip after unit turned off.
|
|
|
Submitted 538 days ago | by
colin, hastings
Answered 536 days ago | The Doc
|
|
Q: Cold water not apparantly sufficient to make correct temperature - in otherwords water is very much hotter than usual for the control setting. When control at coldest setting virtually no water from shower head.
Think its a bit noisier.
|
|
|
Submitted 539 days ago | by
Ed, Northampton
A: Could be a few things however first check that the filters are clean Answered 536 days ago | The Doc |
|
|
Q: My Mira Event Xs Thermostatic continues to run for about 10 minutes after it has been switched off. What Part do I need to order to repair it and how much will that particular part cost?
|
|
|
Submitted 553 days ago | by
Larsey
Answered 550 days ago | The Doc
|
|
Q: hi , had this mira replaced a year ago , am sure document said it carried 5 yr guarantee , but mira insisting it is one year , will need to check , have box in the loft.
any way now shower developed intermintant fault , it turns on and then swithces off after a few mins. Notice the light on on/off button does not seem to work but shower operates when it wants to .
Any suggestions what may be the problem and or solution?
many thanks
|
|
|
Submitted 584 days ago | by
atul
A: It may be your solenoid valve, you can check it if you have a multi meter, you should have a reading of at least k3.5 ohms, across the two terminals any less and you need a new valve. (Check the valve in the failed state.) (When it is not working!) If there is power getting to the solenoid and it is not operating then there is a good chance that you have a faulty solenoid. If you don’t have a multimeter we sell them with a guide on how to use them for checking and testing the various parts of your shower. Apart from helping to fix your shower, they are really useful for checking you have a power supply to appliances, for checking fuses and letting you know much power you have left in batteries (So you will know if they are good or not) and lots of other jobs, in short they are well worth a few pounds http://www.showerdoc.com/installation/electrical-products/SKYTRO-600-005-Digital-Multi-Tester Answered 583 days ago | Anonymous |
|
|
Q: Oval switch has popped off, we still have it but can't get it to stay on as it just keeps popping off. Any suggestions?? Apart from that shower is fantastic. Jill
|
|
|
Submitted 633 days ago | by
Jill
A: It sounds like your retainer that attaches to the rear of the button has broken meaning the button wont stay on.
You will need to order item number 6 from the Event XS spares diagram which is part number MIRA-453.05, This is the cover assembly white with the button attached as the button is not available separate. Answered 631 days ago | SD |
|
Q: Have you a replacement switch for this shower? It is item c in the diagram.
How much would it cost?
Thanks
Jim
|
|
|
Submitted 639 days ago | by
Jimmy
A: If you are looking for item C from the Mira Event XS Thermostatic diagram then you need to order the Harness assembly part number 453.10 wich includes the switch
Answered 635 days ago | SD |
|
Q: i have a Mira event xs thermastatic shower & i need the on / off button which is on your parts list marked C with no number.
Is it possible to obatain this part on its own.
Regards.
Anne
|
|
|
Submitted 639 days ago | by
anne
A: If you are looking for item C from the Mira Event XS Thermostatic diagram then you need to order the Harness assembly part number 453.10 wich includes the switch Answered 635 days ago | SD |
|
Q: Our shower has no hot water pressure, when turned to cold water the pressure is as expected but when switched to hot water the pressure is minimal with water coming out with a spitting effect. My mum called out a plumber who refered us to your company and said it may be the selanoid part?
I was wondering the possible effect of this and a rough guide for it being fixed including call out charges, labour and the parts?
Many thanks
Ivan Osburn
|
|
|
Submitted 660 days ago | by
Ivanoz198406
A:
Our service engineers only cover Edinburgh and surrounding area, but I would suggest that you get the inlet filters checked as it sounds like the hot may be blocked. The manual will show where these are.
Answered 660 days ago | Alastair |
|
|
Q: The oval cover for our switch popped off this morning and has disappeared down the plug hole. Is it possible to get a replacement cover?
|
|
|
Submitted 744 days ago | by
Jak
A: As the button is not available the front cover would be needed and the part number required is 453.05 Answered 744 days ago | SD |
|