Mira Vie

A: It comes fully assembled.

A: 

 

Difficult to say without actually hearing the noise howeverit is most likely to be coming from the solenoid valve, or it is possible thatyou are hearing the water passing through the flow valve at high pressure.

 

In either case it may be the beginning of the end for eithercomponent however as they can carry on like this for a long time I would notworry about it immediately also we have these parts in stock so we can dispatchthe same day as order.

 

A: 

Ifyou have power to the isolating switch and no power getting to the shower thatpoints to a faulty isolating switch.

 

A: 

I think you need a new flow regulator assembly

 http://www.showerdoc.com/MIRA-1539-379-Mira-Flow-Regulator-Assembly-1539-379

A: 

If you have fitted the head that came with the unit thenthat is the correct head.

 

Is the shower connected to the water mains and have you gota pressure of at least 1 bat in the mains.

 

You could give your local water authority a ring an ask themwhat your water pressure should be, they will probably say that the supply aminimum of 1bar (the minimum required to operate a shower)however pressthem and ask what it is likely to be first thing in the morning (when everybodyis showering)

 

They could have the pressure turned down because they areworking on the main, or because there is a burst pipe some where and they haveturned the pressure down to try to save water, or the pressure maybe low justbecause there is a burst pipe somewhere, that hasn’t been discovered yet!

A: Check the shower hose is not kinked or collapsed internally and the head is clear.
Check that incoming mains water stopcock and any isolation valve in feed to the azhower are fully open.
Check with your  supplier if there has been any reduction in water supply flow or pressure.
Check that gauze filter in inlet to solenoid valve is clear.
If all above are ok then it is the stabiliser/flow valve at fault , repair kit can be ordered online by clicking on the link below.

http://www.showerdoc.com/shower-spares/mira/MIRA-1539-379-Mira-Flow-Regulator-Assembly-1539-379

A: This is a fault of the solenoid coil on the flow regulator assy , replacement flow regulator to suit thw wattage of your shower can be ordered online via the link below.

http://www.showerdoc.com/shower-spares/mira/MIRA-PARENT-24-Mira-Vie

A: 

It sounds like a faulty switch which is part of the flow regulator assembly.

http://www.showerdoc.com/shower-spares/mira/MIRA-PARENT-24-Mira-Vie

 

For 7.5 8.5 units

http://www.showerdoc.com/shower-spares/mira/MIRA-1539-379-Mira-Flow-Regulator-Assembly-1539-379

For 9.5 and 10.8 units

http://www.showerdoc.com/shower-spares/mira/MIRA-439-78-Mira-Flow-Regulator-Assembly-(9-5---10-8kw-Models)-439-78

A: 

The things to check first are.

1 That the main valve coming into your house is fully open.

2 Then check that the valve on the line to the shower is fully open.

If these valves are not fully open then there may not be enough water
getting to your shower to cool it properly the overheat safety device will turn
the power off until it cools Then it all starts again

Make sure that the shower head is clean and clear, that the hose isn’t kinked (this can happen just behind the hand set where it is difficult to see) also check the inside of the hose although it can look OK on the outside it could have collapsed internally

The other possibility is a faulty flow/stabilizer valve not allowing the correct amount of water into the shower.

http://www.showerdoc.com/shower-spares/mira/MIRA-1539-379-Mira-Flow-Regulator-Assembly-1539-379

 

A: 

It may be a faulty element in the heating tank (there are two, three in most 10kw showers) you can check them with a multi meter you should have a reading of around 12>18 ohms.

If you have power to the elements and no heat it's probably the elements, no power to the elements then it's probably a micro switch.

 

If you don’t have a multimeter  we sell them at £10 each with a guide on how to use them for checking and testing the various parts of your shower.

 

Apart from helping to fix your shower, they are really useful for checking you have a power supply to appliances, for checking fuses, letting you know much power you have left in batteries

(so you know if they are dud or not)  and lots of other jobs, in short they are well  worth the £10.

 

http://www.showerdoc.com/installation/electrical-products/SKYTRO-600-005-Digital-Multi-Tester