MENU

Triton T90si Pumped Shower Spares

TRITO-PARENT-19

Triton
Triton T90si Pumped Shower Spareshover to zoom or click to enlargeclick here to view full size

Product Details

Spares
Questions and Answers
Do you have a question regarding this product? Call us on directly 0131 538 4343 or ask us a question now. ? Ask new question

Please fill out the form below to submit your question

You browser doesn't have Flash, Silverlight, Gears, BrowserPlus or HTML5 support.

You browser doesn't have Flash, Silverlight, Gears, BrowserPlus or HTML5 support.

Whistling noise 1 Answer

Q: When the shower has been running for a few minutes it starts to make a whistling noise,also has become very noisy

Submitted 40 days ago | by Shaychef, Dublin
! Answer this question
A: This could be the flow valve or the pump that is causing the fault, I think you will need to do a little more investigation.Answered 39 days ago | The Doc
Water temperature has dropped 1 Answer

Q: Hi, I appreciate any help you can give. Triton T90si - water temperature has dropped and dial needs to be put at 9 or 10 (previously 3 or 4) to get warm water but then the pressure is terrible. I have checked the solenoid, tco, elements with a multimeter and all seem fine. I then noticed that when the shower was on there is no power getting to one of the elements from the micro-switch. How do I check this please?

Submitted 158 days ago | by Murt, Ireland
! Answer this question

A: I would normally suspect a faulty element.

However if there is no power getting to one of the elementsas you suggest it sounds like a faulty micro switch.

Basically if there is powergetting to the micro switch and not coming from the switch when it is supposedto be in the on position then the switch is faultyAnswered 157 days ago | The Doc
T90si 1 Answer

Q: just in relation to t90si with no noise, I mean the shower makes no noise at all now when it is switched on ie as in no pump/ motor noise ! yet cold water flows from the shower head. I am in a limescale area too.

Can it still be a TCO issue or the filter.

Submitted 235 days ago | by uisce, meath
! Answer this question
A: First check that you have 230-240v at the connector block, then take it from there.Answered 235 days ago | Barrie
T90si with no noise 1 Answer

Q: Problem with shower, no noise when put on. even though light on in unit only cold water flowing through. Could it be the pump? It had made some noise a few days ago and the whole unit cut out.

Submitted 235 days ago | by uisce, meath
! Answer this question
You need to test if you are getting 230-240v in the shower at the connecting block. And if so,
A:

if the shower is absolutely cold then I think you may have a faulty Thermal Cut Out
A faulty TCO will have no continuity across the two terminals (Theblack thing on top of the heating tank)
Therefore agood TCO will have power at both connections and a faulty TCO will have power atonly one.
(The function of the TCO is, if thewater over heats it cuts the power off to the elements)

SeeVideo.

http://www.youtube.com/user/showerdoc#p/u/2/_zi8JbEMYMs

If there is some heat it may be a faultyelement in the heating tank (there are two, three in most 10kw showers) you cancheck them with a multi meter you should have a reading of around 12>18 ohms.

If you have power to the elements and noheat it's probably the elements, no power to the elements then it'sprobably a micro switch.

If you don’t have a multimeter we sell themat £10 each with a guide on how to use them for checking and testing the variousparts of your shower.

Apart from helping to fix your shower, theyare really useful for checking you have a power supply to appliances, forchecking fuses, letting you know much power you have left in batteries

(so you know if they aredud or not) and lots of other jobs, in short they are well worth the £10.

http://www.showerdoc.com/installation/electrical-products/SKYTRO-600-005-Digital-Multi-Tester

Answered 235 days ago | Barrie
t90 wont work 1 Answer

Q: my triton t90 wont work, when the water is switched on it makes a very loud noise and no water come through it,

Submitted 280 days ago | by Derek, Clonsilla
! Answer this question

A: It maybe your solenoid valve, you can check it if you have a multi meter, you shouldhave a reading of at least k3.5 ohms, across the two terminals any less and youneed a new valve. (Check the valve in the failed state.) (When it has stoppedworking!)

If thereis power getting to the solenoid and it is not operating then there is a goodchance that you have a faulty solenoid.

http://www.youtube.com/watch?v=NzJjzWqxesc

The video is intended as a guide and does not cover every shower.

If youdon’t have a multimeter we sell them with a guide on how to usethem for checking and testing the various parts of your shower.

Apart from helping to fix your shower, they are really useful forchecking you have a power supply to appliances, for checking fuses and lettingyou know much power you have left in batteries

(So youwill know if they are good or not) and lots of other jobs, in short they arewell worth a few pounds

http://www.showerdoc.com/installation/electrical-products/SKYTRO-600-005-Digital-Multi-Tester

Answered 279 days ago | Barrie
PART FOR HOLDING THE SHOWER HEAD 1 Answer

Q: I need to get the part that actually holds the shower head, my one is broken so the shower head just hangs down

Submitted 327 days ago | by Lor , Ireland
! Answer this question
Measuring through the centre of your shower rail outside edge to outsideedge, will give its diameter and you can use this to find the correct size whenchoosing a slider bracket which will fit. A: http://www.showerdoc.com/shower-accessories/slider-bracketsAnswered 327 days ago | Barrie
T90Si leak 1 Answer

Q: Leak appears to be from the flow valve. Is this easy to change?

Submitted 370 days ago | by g_rune, Dudley
! Answer this question

A: For me no!

However I don’t know how much of this sort ofthing you have done before ....This video may help.

http://www.youtube.com/watch?v=LLdiGvZmyGo

Answered 369 days ago | The Doc
T90Si leak 1 Answer

Q: water runs down wall around the middle of the unit so not from PRD dont think its from flow valve either. Now also cutting out after 5 mins or so.

Submitted 374 days ago | by g_rune, Dudley
! Answer this question

A: If it is cutting out after 5mins that would suggest asolenoid valve fault.

If it is leaking then you will need to switch the power offremove the front cover dry the inside out refit the cover switch back on for 10or 15 secs then switch off and try to see where the leak is coming from thenkeep repeating until you have found the leak

Answered 374 days ago | The Doc
water power and heat control 1 Answer

Q: temp has to be turned up to setting 8 to get water m hot, where as it was hot at setting 5 also pressure tends to go up and down.what may have caused this change.how do I fix it

Submitted 382 days ago | by puppydog, nothern ireland
! Answer this question

A: It may be a faulty elementin the heating tank (there are two, three in most 10kw showers) you can checkthem with a multi meter you should have a reading of around 12>18 ohms.

If you have power to theelements and no heat it's probably the elements, no power to the elements thenit's probably a micro switch.

If you don’t have amultimeter we sell them at £10 each with a guide on how to use them forchecking and testing the various parts of your shower.

Apart from helping to fixyour shower, they are really useful for checking you have a power supply toappliances, for checking fuses, letting you know much power you have left inbatteries

(so you know if they are dud ornot) and lots of other jobs, in short they are well worth the £10.

http://www.showerdoc.com/installation/electrical-products/SKYTRO-600-005-Digital-Multi-Tester

Also check the Filter Assembly

Answered 382 days ago | Barrie
part needed 1 Answer

Q: I'm inquiring about a piece for the Triton T90si that you do not have listed as a part, it is the plastic pump reservoir located on your diagram between pieces 4 and 10 , I would like to know if it is possible to get this part and also how much , many thanks

Submitted 387 days ago | by Anonymous, Donegal Ireland
! Answer this question

A: That is the actual pump and unfortunately only comes as partof the motor and pump assembly.

http://www.showerdoc.com/triton-pump-and-motor-assembly-84000110

Answered 384 days ago | The Doc
T90SI Dribbles water 1 Answer

Q: Shower is 5 - 6 years old. When switched on the shower head dribbles water with no noise from the pump. The shower will work one day and the next it will have this problem. I have taken the cover off and moved the fins on the motor and every time I move the fins on the motor it fires up when switched on. Is it a motor/brushes issue?

Submitted 397 days ago | by Dave, Harwich
! Answer this question

A: Sounds like you have a faulty motor and pump unit http://www.showerdoc.com/triton-pump-and-motor-assembly-84000110

Depending on the age of the motor and pump unit you may beable to get away with fitting new brushes.

http://www.showerdoc.com/sintech-motor-carbon-brushes-pair-in-brass-casing-01102

If you are uncertain about the brushes send us a photo ofthe top of the motor and we will make sure you get the correct type

Answered 396 days ago | The Doc
kilowatt rating 1 Answer

Q: I want to replace current triton T90si shower with new triton t90x I am unsure as to kilo watt rating of exiting shower or how to check their is MCB C40 protecting circuit could you advise whether is 8.5 or 9.5 version my shower was purchased in 2004

Submitted 459 days ago | by tadgh, co.clare ,ireland
! Answer this question
A: There should be a lable inside or on the bottom/top of the shower to tell you the kw rating.Answered 459 days ago | Barrie
T90si loosing temp 1 Answer

Q: Hi there, happy new year!



I have a problem with a relatively new Triton T90si....for the last few weeks, when I turn it on, it heats the water for just a few minutes and then the water will only heat to warm, regardless of when setting I use.



I seem to remember this happening to a friend of mine a number of years ago and there was a simple fix...but I can't remember who it was, or what the solution was.



Any help that you can give me will be much appreciated.



Kind regards,

Mitch

Waterford, Ireland

Submitted 474 days ago | by Mitch, Waterford, Rep. of Ireland
! Answer this question

A: If there is some heat it may be a faultyelement in the heating tank (there are two, three in most 10kw showers) you cancheck them with a multi meter you should have a reading of around 12>18 ohms.

If you have power to the elements and noheat it's probably the elements, no power to the elements then it'sprobably a micro switch.

If you don’t have a multimeter we sell themat £10 each with a guide on how to use them for checking and testing the variousparts of your shower.

Apart from helping to fix your shower, theyare really useful for checking you have a power supply to appliances, forchecking fuses, letting you know much power you have left in batteries

(so you know if they aredud or not) and lots of other jobs, in short they are well worth the £10.

http://www.showerdoc.com/installation/electrical-products/SKYTRO-600-005-Digital-Multi-Tester

Answered 472 days ago | Barrie
no pressure on tsi90 1 Answer

Q: shower was fitted 7 years ago but never commisioned till now. after following all the correct procedure i have very little water flow.when shower is turned off water is dribbling all the time from the hose. filter clean,water bled, no blockage from tank upstairs what direction to go now please

Submitted 526 days ago | by bootboys, lymmn
! Answer this question
First check that you have power to the shower, then check that the head and hose are clear.
A:
After all this time the motor maybe seized, try moving the fins with the power of to check. If all is well here then,

it maybe your solenoid valve, you can check it if you have a multi meter, you shouldhave a reading of at least k3.5 ohms, across the two terminals any less and youneed a new valve. (Check the valve in the failed state.) (When it has stoppedworking!)

If thereis power getting to the solenoid and it is not operating then there is a goodchance that you have a faulty solenoid.

http://www.youtube.com/watch?v=NzJjzWqxesc

The video is intended as a guide and does not cover every shower.

If youdon’t have a multimeter we sell them with a guide on how to usethem for checking and testing the various parts of your shower.

Apart from helping to fix your shower, they are really useful forchecking you have a power supply to appliances, for checking fuses and lettingyou know much power you have left in batteries

(So youwill know if they are good or not) and lots of other jobs, in short they arewell worth a few pounds

http://www.showerdoc.com/installation/electrical-products/SKYTRO-600-005-Digital-Multi-Tester

Answered 524 days ago | Barrie
triton shower making noise 1 Answer

Q: after water supply was turned off my shower has been making a screeching noise. everything working fine on it just the noise

Submitted 532 days ago | by mich, kildare ireland
! Answer this question
Thethings to check first are:
A:
1 That the main valve coming into your house is fullyopen.

2 Then check that thevalve on the line to the shower is fully open.

If these valves are not fully open then there may not beenough water getting to your shower.Answered 531 days ago | Barrie
Replacement o-rings 1 Answer

Q: My Triton T90si has sprung a drip from the filter assembly. I think in only needs the o-ring replaced. Can you suggest a suitable pack of o-rings so I can replace them while replacing them.



Thanks, Mark

Submitted 534 days ago | by Mark, Paisley
! Answer this question
A: There are various "O" ring packs on the market, but it would be more cost effective to take your "O" rings into a local plumb store to replace them, than trying to find one of these packs, as not all the "O" rings may be suitable for your shower.Answered 531 days ago | Barrie
triton shower t 90 si 1 Answer

Q: what causes my shower to make a loud noise when in use

Submitted 543 days ago | by gorvagh, mohill co leitrim
! Answer this question

A: I don’t know what type of noise you are hearing, however there is a pump inside or per the water starting to boil like the noise a kettle makes

Answered 541 days ago | The Doc
T90si....Water very hot 1 Answer

Q: Water very hot at low setting........ Shower used to make a sound like something was kicking in after a few seconds but it does not do this now. What could the problem be??

Submitted 548 days ago | by Animal7, Republic of Ireland.
! Answer this question

A: Sounds like there is not enough water passing through it to cool it properly

Check that the inlet filter is clean and clear.

Make sure that the shower head is clean and clear, that the hose isn’t kinked (this can happen just behind the hand set where it is difficult to see) also check the inside of the hose although it can look OK on the outside it could have collapsed internally


Answered 545 days ago | The Doc
Triton T90si 1 Answer

Q: Water coming out is cold.Continuity across tco - ok. Heating elements- ok. 240 v at Terminal block.27mv at tco.there is continuity between Terminal block and tco. Indicator light coming on ok.Motor is not turning. Could it be brushes.

Submitted 556 days ago | by Peter, Dublin ,Ireland
! Answer this question
First test the outlet TCO, then, if the motor is not running and there is power to it and depending on the condition of the pump you may get away with just fitting a new set of brushes.

A: http://www.showerdoc.com/hydr-01102-hydra-sintech-motor-carbon-brushes-(pair)---in-brass-casing-01102

Answered 555 days ago | Barrie
heater cutting in out 1 Answer

Q: when shower is on the water goes hot and cold

Submitted 564 days ago | by shower, wexford
! Answer this question

A: The things to check first are:

1 That the main valve coming into your house is fully open.

2 Then check that the valve on the line to the shower is fully open.

If these valves are not fully open then there may not be enough water getting to your shower.

Make sure that the shower head is clean and clear, that the hose isn’t kinked (this can happen just behind the hand set where it is difficult to see) also check the inside of the hose although it can look OK on the outside it could have collapsed internally

The other possibility is a faulty flow/stabilizer valve not allowing the correct amount of water into the shower.

A rough check is to remove the shower head turn temperature control to fully hot the water coming out of the hose should be a bit more than a dribble then turn to fully cold and it should be coming out at full flow.

If there is not much difference between the two then you could have a faulty flow valve.

Carry out this check after you check the inlet valves.

Also if it is a Triton have a look at the outlet TCO

The outlet Thermal Cut Out this is a black disk with two wires going to it and it is mounted on the out let pipe (The bit between the heating tank and the hose)


Examine the connections closely if you see any discoloration / signs of overheating then the TCO needs replaced.

Open / close the safety device that allows power through to the elements

Answered 563 days ago | Barrie
T90SI Leaking 1 Answer

Q: My shower is leaking via the shower-head. I have replaced the PRD but the water is still dripping from that valve assembly and out through the shower head,

Submitted 569 days ago | by farmacy, Ludlow
! Answer this question

A: It may be your solenoid valve, you can check it if you have a multi meter, you should have a reading of at least k3.5 ohms, across the two terminals any less and you need a new valve. (Check the valve in the failed state.) (When it has stopped working!)

If there is power getting to the solenoid and it is not operating then there is a good chance that you have a faulty solenoid.

http://www.youtube.com/watch?v=NzJjzWqxesc

The video is intended as a guide and does not cover every shower.

If you don’t have a multimeter we sell them with a guide on how to use them for checking and testing the various parts of your shower.

Apart from helping to fix your shower, they are really useful for checking you have a power supply to appliances, for checking fuses and letting you know much power you have left in batteries

(So you will know if they are good or not) and lots of other jobs, in short they are well worth a few pounds

http://www.showerdoc.com/installation/electrical-products/SKYTRO-600-005-Digital-Multi-Tester

Answered 569 days ago | Barrie
Motor brushes T90si 1 Answer

Q: Hi can you send me the link to find motor brushes fot Triton T90si.



Many thanks.

Submitted 584 days ago | by David, New Ross, Ireland
! Answer this question
changing showers 1 Answer

Q: my T90si has broken, I have a Triton Ivory II, 10.5

Will this shower be ok to replace the T90si?

Submitted 618 days ago | by stevie, Dublin, Ireland
! Answer this question

A: I am afraid that the Ivory is not a suitable replacement

The T90si is a pumped electric shower and will need replacedby a pumped electric with the same output as your existing shower.

http://www.showerdoc.com/showers/pumped-electric

Answered 615 days ago | The Doc
Interchangeability 1 Answer

Q: If I need to replace the entire unit, Are there other showers which are dimensionally and electrically interchangeable?

Submitted 655 days ago | by Colin1956, Warrington
! Answer this question

A: The T90XR is pretty much a direct change over.

http://www.showerdoc.com/showers/pumped-electric/triton

There are an 8.5 and 9.5 version check the output on your existing shower before ordering.

Answered 654 days ago | The Doc
motor speeding up 1 Answer

Q: hi showerdoc

my tiiton T90si pump has started to speed up then slow down after about 2 mins of working ok.The water temperature will get hotter when it speeds up then cold when it slows down,i have replaced the brushes and changed the solenloid vaulve but still no good can you help?

Submitted 676 days ago | by camalot, ireland
! Answer this question
a
A: Answered 676 days ago | The Doc
T90si constant dripping 1 Answer

Q: When shower is turned off water drips constantly from shower head. What is most likely cause ? It's been dripping for 3 days. shower is over 3 years old.

Submitted 758 days ago | by Barry, Ireland
! Answer this question

A: You will need to replace the complete solenoid valve

http://www.showerdoc.com/shower-spares/triton/TRITO-22009110-Triton-Solenoid-Valve-22009110

Answered 755 days ago | The Doc
Trition T 90i compatibility or spares 1 Answer

Q: Good morning the TCO on my Triton t90i is burned out. Is the TCo from the T90si (8.5 Kw) compatiable or would you have the correct TCO.

Regards.

Johnny

Submitted 802 days ago | by Johnny150, Republic of Ireland
! Answer this question
shower stopped 1 Answer

Q: the motor does not work when you turn on the shower

Submitted 836 days ago | by Anonymous, Unknown
! Answer this question

A: It sounds like you need a new motor and pump unit or you mayget away with just fitting a new set of brushes to the motor.

We would always advise changing the complete motor and pumpunit however the brushes are much cheaper.

Answered 832 days ago | The Doc
Triton T90si micro switch 1 Answer

Q: what is a micro switch and how do you change it. How do you know its gone.

Submitted 876 days ago | by Colm, Ireland
! Answer this question

A: Sorry for the delay in replying

A micro switch is a switch that switches power on and off

A faulty micro switch will be stuck on allowing power to pass through it all the time or off not allowing power through it at al.

How to change it.......It depends where it is and which one has gone.

Answered 867 days ago | The doc
T90si 1 Answer

Q: How much are a set of brushes. If one element goes can you replace it or do you have to buy aheater can. Where does the solenoid valve sit on the solenoid. Is the coil all part of the solenoid. Is the mould removal spray to remove mould from the shower tray. Are your parts genuine Triton parts. Thanks for your help. Kind regards Colm.

Submitted 881 days ago | by colm, Unknown
! Answer this question

A: How much are a set of brushes.

There no brushes available for this motor at this time

If one element goes can you replace it or do you have to buy aheater can.

You have to buy the can

Where does the solenoid valve sit on the solenoid.

On the rear case?

 Is the coil all part of the solenoid.

Yes but it can be removed.

Is the mould removal spray to remove mould from the shower tray.

Yes If the mould is on silicone (A soft surface it may take more than one application)

 Are your parts genuine Triton parts.

All our parts are OME unless otherwise stated or described as universal

Thanks for your help. Kind regards Colm.

No problem!

Answered 880 days ago | The Doc
triton t90si electric shower cool 1 Answer

Q: Our shower was running when the power in the house tripped. Now to get only just warm water the control has to be up at 10 max and of course the flow is then fairly weak. There is also a bit of pulsing in the flow as it runs .Any ideas re bleeding or am I in bigger trouble?

Submitted 890 days ago | by gramscot, ireland
! Answer this question

A: It may be a faulty element in the heating tank (there are two, three in most 10kw showers) you can check them with a multi meter you should have a reading of around 12>18 ohms.

If you have power to the elements and no heat it's probably the elements, no power to the elements then it's probably a micro switch.

 

If you don’t have a multimeter  we sell them at £10 each with a guide on how to use them for checking and testing the various parts of your shower.

 

Apart from helping to fix your shower, they are really useful for checking you have a power supply to appliances, for checking fuses, letting you know much power you have left in batteries

(so you know if they are dud or not)  and lots of other jobs, in short they are well  worth the £10.

http://www.showerdoc.com/installation/electrical-products/SKYTRO-600-005-Digital-Multi-Tester

Answered 888 days ago | The Doc
Motor Brushes 1 Answer

Q: Can the motor brushes be bought separately?

& do you post to ireland?

Submitted 891 days ago | by Ian, Ireland
! Answer this question

A: The brushes come in pairs and Ireland is no problem, when you reach check out the Ireland options are available

Answered 888 days ago | The Doc
shower not working 1 Answer

Q: my triton t90si shower which was installed approx 7 years ago has never been used it sounds funny when turned on with only a dribble of water from it absolutely no pressure, any ideas?

Submitted 893 days ago | by mike, nenagh ireland
! Answer this question

A: Is the pump running?

Ate the valves that supply the unit fully open?

The flow valve may be stuck due to lack of use, you could try winding it back and forth fully hot to fully cold 20 or 30 times it may free it off.

Answered 892 days ago | The Doc
triton t90 si too hot 2 Answers

Q: when shower is turned on water too cold and when adjusted water gets too hot,will not maintain medium temp,even with slight adjustment.

Submitted 909 days ago | by Anonymous, kilkenny,rep of ireland
! Answer this question

A: It maybe a faulty element in the heating tank (there are two, three in most 10kwshowers) you can check them with a multi meter you should have a reading ofaround 12>18 ohms.

If you have power to the elementsand no heat it's probably the elements, no power to the elements thenit's probably a micro switch.

If you don’t have amultimeter  we sell them at £10 each with a guide on how to use them forchecking and testing the various parts of your shower.

Apart from helping to fix yourshower, they are really useful for checking you have a power supply to appliances,for checking fuses, letting you know much power you have left in batteries

(so you know if they are dud ornot)  and lots of other jobs, in short they are well  worth the £10.

http://www.showerdoc.com/installation/electrical-products/SKYTRO-600-005-Digital-Multi-Tester

Answered 908 days ago | Anonymous

A: It maybe a faulty element in the heating tank (there are two, three in most 10kwshowers) you can check them with a multi meter you should have a reading ofaround 12>18 ohms.

If you have power to the elementsand no heat it's probably the elements, no power to the elements thenit's probably a micro switch.

If you don’t have amultimeter  we sell them at £10 each with a guide on how to use them forchecking and testing the various parts of your shower.

Apart from helping to fix yourshower, they are really useful for checking you have a power supply to appliances,for checking fuses, letting you know much power you have left in batteries

(so you know if they are dud ornot)  and lots of other jobs, in short they are well  worth the £10.

http://www.showerdoc.com/installation/electrical-products/SKYTRO-600-005-Digital-Multi-Tester

Answered 908 days ago | The Doc
hose 2 Answers

Q: which replacement hose would i use for this shower?

Submitted 910 days ago | by clio, Unknown
! Answer this question

A: Any of these hoses will fit

http://www.showerdoc.com/shower-accessories/shower-hoses/triton

It is really just a case of deciding on the length.

Answered 909 days ago | The doc

A: Any of these hoses will fit

http://www.showerdoc.com/shower-accessories/shower-hoses/triton

It is really just a case of deciding on the length.

Answered 909 days ago | The doc
triton t90i no water 1 Answer

Q: when you turn on shower led lights and it makes noise but nothing happening is motor burnt out

Submitted 915 days ago | by lorcan, dublin
! Answer this question

A: It may be your solenoid valve, you can check it if you havea multi meter, you should have a reading of at least k3.5 ohms, across the twoterminals any less and you need a new valve. (Check the valve in the failedstate.) (When it has stopped working!)

 

If there is power getting to the solenoid and it is notoperating then there is a good chance that you have a faulty solenoid.

http://www.youtube.com/watch?v=NzJjzWqxesc

The videois intended as a guide and does not cover every shower.

 

If you don’t have a multimeter  we sell them  with a guide on how to use them for checkingand testing the various parts of your shower.

 

Apart from helping to fix your shower, they are reallyuseful for checking you have a power supply to appliances, for checking fusesand letting you know much power you have left in batteries

(So you will know if they are good or not) and lots of otherjobs, in short they are well worth a few pounds

http://www.showerdoc.com/installation/electrical-products/SKYTRO-600-005-Digital-Multi-Tester

http://www.showerdoc.com/shower-spares/triton/TRITO-22009110-Triton-Solenoid-Valve-22009110

Answered 914 days ago | The Doc
Triton T90SI Cold 1 Answer

Q: Shower problem - no hot water just cold water

Submitted 916 days ago | by John, Maynooth Co. Kildare Ireland
! Answer this question

A: If the shower is absolutely cold then I think you may have a faulty Thermal Cut Out
A faulty TCO will have no continuity across the two terminals (The black thing on top of the heating tank)
Therefore a good TCO will have power at both connections and a faulty TCO will have power at only one.
(The function of the TCO is, if the water over heats it cuts the power off to the elements)

See Video.

http://www.youtube.com/user/showerdoc#p/u/2/_zi8JbEMYMs

If there is some heat it may be a faulty element in the heating tank (there are two, three in most 10kw showers) you can check them with a multi meter you should have a reading of around 12>18 ohms.

If you have power to the elements and no heat it's probably the elements, no power to the elements then it's probably a micro switch.

 

If you don’t have a multimeter  we sell them at £10 each with a guide on how to use them for checking and testing the various parts of your shower.

 

Apart from helping to fix your shower, they are really useful for checking you have a power supply to appliances, for checking fuses, letting you know much power you have left in batteries

(so you know if they are dud or not)  and lots of other jobs, in short they are well  worth the £10.

http://www.showerdoc.com/installation/electrical-products/SKYTRO-600-005-Digital-Multi-Tester

Answered 915 days ago | The Doc
water only very hot 1 Answer

Q: My triton t90si is only supplying very hot water no matter what the dials are set to.

Submitted 920 days ago | by Kev, uk
! Answer this question
Check the shower hose is not kinked or collapsed internally and the shower head is clear'
A: Check the inlet filter is clear and that any isolation valve in feed is fully open.
If all above are ok then it is likely to be the flow valve at eault , replacement can be ordered online by clicking on the link below.

http://www.showerdoc.com/shower-spares/triton/TRITO-82100310-Triton-Flow-Valve-Assy-82100310Answered 917 days ago | Alastair
Power Level 1 Answer

Q: Hi,



The power of the shower is very poor, yet theater flow at the taps is good. We have tried tthe power settings but this only increases the temperature. Is there anything else that might not be working?



Thanks.

Submitted 996 days ago | by Dean, Stafford
! Answer this question

A: These showers are not very powerful however they should provide an acceptable shower.

However there two things that may be worth checking.

The outlet TCO

The outlet Thermal Cut Out this is a black disk with two wires going to it and it is mounted on the out let pipe  (The bit between the heating tank and the hose)

Examine the connections closely if you see any discoloration / signs of overheating then the TCO needs replaced.   

The Elements

It may be a faulty element in the heating tank (there are two, three in most 10kw showers) you can check them with a multi meter you should have a reading of around 12>18 ohms.

If you have power to the elements and no heat it's probably the elements, no power to the elements then it's probably a micro switch.

 

If you don’t have a multimeter  we sell them at £10 each with a guide on how to use them for checking and testing the various parts of your shower.

 

Apart from helping to fix your shower, they are really useful for checking you have a power supply to appliances, for checking fuses, letting you know much power you have left in batteries

(so you know if they are dud or not)  and lots of other jobs, in short they are well  worth the £10.

http://www.showerdoc.com/installation/electrical-products/SKYTRO-600-005-Digital-Multi-Tester

Answered 993 days ago | The doc
Faulty solenoid in Triton t90 si pumped 1 Answer

Q: water continues to run for a while after shut off

Submitted 1003 days ago | by leon, cheshire
! Answer this question
A: http://www.showerdoc.com/TRITO-22009110-Triton-Solenoid-Valve-22009110

Sounds like the solenoid is not closing properly. Above is a link to the part.Answered 1003 days ago | Bar S
Triton T90 Internal Wiring 1 Answer

Q: My element was clogged with lime so I removed it and used a chemical to disolve the lime. The problem now is I cant find the wiring chart i made. Do you have a diagram of the wiring at the top of the heater element or a photo of where the wires go?

Submitted 1014 days ago | by Boxer Boy, Dublin
! Answer this question

A: Sorry we don’t have any wiring diagrams perhaps you can try Triton

http://www.tritonshowers.co.uk

Answered 1013 days ago | The Doc
shower going hot / cold 1 Answer

Q: The temperature of the water is going from hot to cold and visa versa throughout the shower time.

Submitted 1016 days ago | by Audrey, Co. Tipperarty, Ireland
! Answer this question

A:
Check that the valve on the line to the shower is fully open.

If these valves are not fully open then there may not be enough water
getting to your shower to cool it properly, also check that the filters are clear

Make sure that the shower head is clean and clear, that the hose isn’t kinked (this can happen just behind the hand set where it is difficult to see) also check the inside of the hose although it can look OK on the outside it could have collapsed internally Answered 1014 days ago | The Doc
Triton t90is leaking 1 Answer

Q: Can I buy the bottom part of the pump assembly as mine has bust where it is connected by four screws and what could cause this to happen .

Submitted 1021 days ago | by Wet, Dublin
! Answer this question

A: I am afraid it only comes as a complete assembly and think it is an unusual place for it to go unless it has been subjected to, too much pressure.

Is it connected to the water mains?

Answered 1021 days ago | The Doc
triton t90si trips out 1 Answer

Q: switch shower on while cold works but soon as you switch it to warm or hot it trips electric switch off.

Submitted 1043 days ago | by handyandy, rowley regis
! Answer this question

A: It may be a faulty element in the heating tank (there are two, three in most 10kw showers) you can check them with a multi meter you should have a reading of around 12>18 ohms.

If you have power to the elements and no heat it's probably the elements, no power to the elements then it's probably a micro switch.

 

If you don’t have a multimeter  we sell them at £10 each with a guide on how to use them for checking and testing the various parts of your shower.

 

Apart from helping to fix your shower, they are really useful for checking you have a power supply to appliances, for checking fuses, letting you know much power you have left in batteries

(so you know if they are dud or not)  and lots of other jobs, in short they are well  worth the £10.

http://www.showerdoc.com/installation/electrical-products/SKYTRO-600-005-Digital-Multi-Tester

Answered 1042 days ago | The Doc
t90si Power 1 Answer

Q: shower will not work, there is power to the mains pull switch the neon light is on, turn the unit on and the mains light goes out and nothing works, turn the unit off again the mains neon light comes back on ? its got me beat

Submitted 1060 days ago | by frankie, donegal
! Answer this question

A:

 You have a faulty isolating switch 

http://www.showerdoc.com/electrical-products/ELWBG002-45-Amp-Ceiling-Switch

Answered 1059 days ago | The Doc
T90si no power 1 Answer

Q: hello the shower has not be used in about 8 weeks went to trun on and no light came on but when i truned on the the power for the shower the light came on there but not on the shower but when i pushed the start stop botton on the shower the light went off and on do you know what this could be

Submitted 1060 days ago | by frankie, donegal
! Answer this question

A: If the light on the isolation switch is going out when you turn the shower on then I think that the isolation switch may be faulty

Answered 1060 days ago | The Doc
tritonT90 SI water leaking 1 Answer

Q: water is leaking from the top of can,around area of thermal cut-out,what is my best option?

Submitted 1075 days ago | by dev, ireland
! Answer this question

A: This is an unusual place for it to leak however if it is leaking from the can then it is just a case of replacing the can.

http://showerdoc.com/shower-spares/triton/TRITO-PARENT-19-Triton-T90si-Pumped

Answered 1074 days ago | The doc
T90si No Water Flow 1 Answer

Q: Shower overheated and then cut-out. 230V at terminal block but LED on front of panel doesn't light. No water flow, but I get flow when I open the bleed valve. Checked TCO and it's faulty (no continuity) so gonna order a new one. Is there another problem, because I thought I'd get cold water flow if TCO faulty? Can you help before I order TCO? Thanks

Submitted 1103 days ago | by Peadar, Galway,Ireland
! Answer this question

A: Yes you are correct, I think you should also check the solenoid.

It may be your solenoid valve, you can check it if you have a multi meter, you should have a reading of at least k3.5 ohms, across the two terminals any less and you need a new valve. (Check the valve in the failed state.) (When it is not working!)

If there is power getting to the solenoid and it is not operating then there is a good chance that you have a faulty solenoid.

If you don’t have a multimeter  we sell them  with a guide on how to use them for checking and testing the various parts of your shower.

Apart from helping to fix your shower, they are really useful for checking you have a power supply to appliances, for checking fuses and letting you know much power you have left in batteries

(So you will know if they are good or not) and lots of other jobs, in short they are well worth a few pounds

http://www.showerdoc.com/installation/electrical-products/SKYTRO-600-005-Digital-Multi-Tester

Answered 1102 days ago | The Doc
triton t 90 cold/cool 2 Answers

Q: water comming from shower always cold

Submitted 1146 days ago | by jess, ireland
! Answer this question
It is likely to be the thermal cut out on top of the heating can which has failed, if you click on the link below it will take you to a video clip showing how to test the tco and allow online ordering.
A:
http://www.showerdoc.com/shower-spares/triton/TRITO-22010070-Triton-Thermal-Cut-Out-22010070

If the tco is ok then with unit on check that the piston on top of the flow valve is activating the microswitch levers and if not a new flow valve can be ordered online by clicking on this link.

http://www.showerdoc.com/shower-spares/triton/TRITO-82100310-Triton-Flow-Valve-Assy-82100310

Check the outlet thermal cut out on the otlet pipe both visually and for continuity and if needed the replacement to suit the wattage of your shower can be ordered via this link.

http://www.showerdoc.com/shower-spares/triton/TRITO-PARENT-19-Triton-T90si-PumpedAnswered 1145 days ago | Alastair

A: If it is absolutely cold then I think you may have a faulty Thermal Cut Out

A faulty TCO will have no continuity across the two terminals (The black thing on top of the heating tank)

Therefore a good TCO will have power at both connections and a faulty TCO will have power at only one.

(The function of the TCO is, if the water over heats it cuts the power off to the elements)

See Video.

http://www.youtube.com/user/showerdoc#p/u/2/_zi8JbEMYMs

If there is some heat it may be a faulty element in the heating tank (there are two, three in most 10kw showers) you can check them with a multi meter you should have a reading of around 12>18 ohms.

If you have power to the elements and no heat it's probably the elements, no power to the elements then it's probably a micro switch.

 

If you don’t have a multimeter  we sell them at £10 each with a guide on how to use them for checking and testing the various parts of your shower.

 

Apart from helping to fix your shower, they are really useful for checking you have a power supply to appliances, for checking fuses, letting you know much power you have left in batteries

(so you know if they are dud or not)  and lots of other jobs, in short they are well  worth the £10.

http://www.showerdoc.com/installation/electrical-products/SKYTRO-600-005-Digital-Multi-Tester

Answered 1145 days ago | The Doc
Triton T90si 2003 1 Answer

Q: Is it possible to buy a replacement heat tank for the 2003 model , or alternatively to buy a complete T90 SI to install in lieu of existing.



1 of the 2 heat elements in the existing tank has failed

Submitted 1152 days ago | by twall, Dublin , RoI
! Answer this question

A: The heating tanks that are available are here

http://www.showerdoc.com/shower-spares/triton/TRITO-PARENT-19-Triton-T90si-Pumped

Items 7 8 and 9

Answered 1151 days ago | The Doc
Only Warm Water 3 Answers

Q: No matter how high I turn my Triton T90si shower, the water is only

lukewarm what is the cause of this? The shower is not very old.

Submitted 1194 days ago | by Mon, Ireland
! Answer this question

A: It may be a faulty element in the heating tank (there are two, three in most 10kw showers) you can check them with a multi meter you should have a reading of around 12>18 ohms.

If you have power to the elements and no heat it's probably the elements, no power to the elements then it's probably a micro switch.

 

If you don’t have a multimeter  we sell them at £10 each with a guide on how to use them for checking and testing the various parts of your shower.

 

Apart from helping to fix your shower, they are really useful for checking you have a power supply to appliances, for checking fuses, letting you know much power you have left in batteries

(so you know if they are dud or not)  and lots of other jobs, in short they are well  worth the £10.

http://www.showerdoc.com/installation/electrical-products/SKYTRO-600-005-Digital-Multi-Tester

Answered 1193 days ago | The Doc

A: It may be a faulty element in the heating tank (there are two, three in 10kw showers) you can check them with a multi meter you should have a reading of around 12>18 ohms.

If you have power to the elements and no heat it's probably the elements, no power to the elements then it's probably a micro switch.

 

If you don’t have a multimeter  we sell them at £10 each with a guide on how to use them for checking and testing the various parts of your shower.

 

Apart from helping to fix your shower, they are really useful for checking you have a power supply to appliances, for checking fuses, letting you know much power you have left in batteries

(so you know if they are dud or not)  and lots of other jobs, in short they are well  worth the £10.

http://www.shower-warehouse.co.uk/erol.html#55x878

Also check the outlet thermal cut out on the outlet pipe to the hose for conyinuity and visual signs of over heating.

Once you have identifiedthe fault required part(s) can be ordered online via the link below.

http://www.showerdoc.com/shower-spares/triton/TRITO-PARENT-19-Triton-T90si-PumpedAnswered 1193 days ago | Alastair

A: It may be a faulty element in the heating tank (there are two, three in 10kw showers) you can check them with a multi meter you should have a reading of around 12>18 ohms.

If you have power to the elements and no heat it's probably the elements, no power to the elements then it's probably a micro switch.

 

If you don’t have a multimeter  we sell them at £10 each with a guide on how to use them for checking and testing the various parts of your shower.

 

Apart from helping to fix your shower, they are really useful for checking you have a power supply to appliances, for checking fuses, letting you know much power you have left in batteries

(so you know if they are dud or not)  and lots of other jobs, in short they are well  worth the £10.

http://www.shower-warehouse.co.uk/erol.html#55x878

Also check the outlet thermal cut out on the outlet pipe to the hose

Once you have identified the fault required part(s) can be ordered online via the link below.

http://www.showerdoc.com/shower-spares/triton/TRITO-PARENT-19-Triton-T90si-PumpedAnswered 1193 days ago | Alastair
triton t90 si Pump 1 Answer

Q: can the plastic bowl beneath the pump and motor be purchased separetly

Submitted 1201 days ago | by jennifer, ireland
! Answer this question
A: Unfortunately no the pump and motor assembly are one componentAnswered 1200 days ago | The Doc
triton 90si going hot cold 1 Answer

Q: the water keeps going hot and old while im in the shower.

Submitted 1291 days ago | by queeny
! Answer this question

A:

Check that the scale trap is clean the shower head is clean and that there no kinks in the hose.

Answered 1290 days ago | Anonymous
Triton T90si TCO 1 Answer

Q: is a seal supplied termal cut-out for the connecting on to the can

Submitted 1392 days ago | by northstar
! Answer this question

A: The TCO lies on top of the tank therefore no seal is necessary

Answered 1391 days ago | The Doc
motor brushes for trition t90si No Answers

Q: Can I buy motor brushes for a trition t90si shower without having to buy the whole motor assembly. Thanks.

Submitted 1447 days ago | by mac
! Answer this question
Motor & Pump Assy. 1 Answer

Q: hi im looking for the part between pump and the filter the one that has the bleed screw is this no 4 or 10 thank you

Submitted 1457 days ago | by jjnulty
! Answer this question

A: I am not certain but I think the part you mention is the pump, which is part of the motor and pump assembly.

This is the pump with the cover removed.

http://www.showerdoc.com/shower-spares/triton/TRITO-84000110-Pump-and-motor-assembly

Answered 1455 days ago | The Doc
Customer Reviews
Be the first to write a review about this product.
Replacement Products
Direct change over

Remember to check you have the same kw rating     

Triton
RRP: £359.70 (inc. VAT)Our Price £276.68 (inc. VAT)Save £83.02
View Item
Related Spares

Please call for more information on available spares for this product